TITEBOND URETHANE WOOD FLOORING REPAIR KIT

The Titebond Urethane Repair Kit is a two-part urethane system that enables contractors to repair loose or popping areas in a finished floor. The adhesive in the system is of low viscosity that sets quickly. The easy flow characteristics of the urethane adhesive, contrary to traditional epoxies, provide increased coverage for the floor repair. The Titebond® Urethane Repair Kit is easy to use with no large holes to drill – a 1/8” drill bit and a caulking gun is all that is required. Therefore, upon completion of the process, when used as directed, the floor will be repaired with no visible defects. This adhesive is good for engineered wood, parquet, solid wood and bamboo flooring. Use with premium caulking gun, minimum of 18:1 thrust ratio recommended.

Features & Benefits

Repairs popping and hollow spots
No visible defects from repair
Easy flow adhesive
Simple assembly process
Highly moisture resistant
Will not cause dimensional changes in wood flooring
Strong ultimate bond
Unaffected by freezing temperatures
Contains no water
Low viscosity
Flows easily
Extremely small hole to drill (1/8" drill bit) for the 1/16" needle on gun
Will not become brittle
Easy assembly process
Quick curing process
Reusable gun

Application Guidelines

Assembly of Titebond Repair System:
1. With the black handle facing forward, insert the black plastic 4:1 ratio plunger into cartridge gun with the flat side going in first.Note: Press upwards on the silver button on rear of gun to allow plunger to slide smoothly backwards. Pull back until plunger is fully retracted.
2. Place 50 ml cartridge into gun making sure to close down the plastic locking mechanism.
3. To remove 50 ml cartridge cap, turn cap 1/4 turn counterclockwise and then pry off. Be sure to hold cartridge upright when removing cap.
4. Remove cap from 50 ml cartridge and twist the clear plastic mixing nozzle onto the cartridge.
5. Place slip-on needle on to mixing nozzle.
Preparation of Repair Area:
1. Locate center of popping or loose area to be repaired.
2. Find a dark grain in the wood flooring piece, to aid in hiding repair.
3. Once the area to repair has been located, place a 2" strip of blue tape where the hole will be drilled. This will mark the spot and aid in the cleanup process.
4. Use 1/8" drill bit and drill a hole through the tape and wood flooring. Drilling on an angle will prevent backflow of adhesive.
To Repair Hole:
1. Insert needle into the 1/8" diameter hole and squeeze the gun handle to begin filling popping area.
2. Continue to squeeze adhesive into the hole until void is filled.
3. Remove the strip of blue tape and wipe away any excess amount of adhesive on the wood with water and a soft cloth or sponge.
4. After filling process is finished, insert toothpick into the hole.
5. After 5-10 minutes, break the toothpick off flush with the floor.
6. Use either colored putty or a crayon to fill excess gap around the toothpick.
Cleanup: Wet adhesive can be cleaned up with water and a soft cloth or sponge. If adhesive has dried, use mineral spirits and a soft cloth. For best results, place a 2" strip of blue tape where the hole will be drilled. Once the repair process is complete, remove the strip of tape with any backflow of adhesive on it and clean remaining amounts with water and a soft cloth or sponge.

Specifications Guide

TOOLS NEEDED:	INCLUDED WITH REPAIR KIT:	OTHER ITEMS NEEDED:
DRILL 1/8" DRILL BIT BLUE TAPE	GUN NEEDLE STATIC MIXING NOZZLE	TOOTHPICK COLOR PUTTY STICK OR CRAYON

Physical Properties

Type: Two-part urethane
Flashpoint (Multithane R2032): Not applicable
State (Multithane R2032):: Liquid
Flashpoint (Hardener 200): > 200°F.
State (Hardener 200): Liquid
VOC (Multithane R2032): Not applicable
Color (Multithane R2032): Beige
VOC (Hardener 200): Not applicable
Color (Hardener 200): Dark brown
Freeze / Thaw Stability: Stable
Storage Life: 2 years

Limitations

Do not leave adhesive stationary in mixing nozzle for more than 10 minutes, as adhesive will cure in nozzle. Prepare all injection sites before using adhesive for best results.

Product SKUs

Part Number	UPC	Case UPC	Size	Weight	Units Per Package	Packages Per Pallet
10003			Cartridges	1.00	12	61
17872			One Dispensing Gun	2.00	1	0

Caution Statement

DANGER: POISON. FUMES HARMFUL. EYE AND SKIN IRRITANT. Do not breathe fumes. Do not get in eyes, on skin, or on clothing. Keep out of reach of children. Use only outdoors or in a well-ventilated area. Wear safety glasses and rubber gloves. Contact causes eye irritation. Prolonged or repeated skin contact or inhalation may cause irritation or allergic reaction. FIRST AID: Contains isocyanate containing polymers. If breathed in, move person into fresh air. If in eyes or on skin, rinse well with water. If on clothes, remove clothes. For more information, see Safety Data Sheet.

Warranty Statement

Important Notice: Our recommendations, if any, for the use of this product are based on tests believed to be reliable. Since the use of this product is beyond the control of the manufacturer, no guarantee or warranty, expressed or implied, is made as to such use or effects incidental to such use, handling or possession or the results to be obtained, whether in accordance with the directions or claimed so to be. The manufacturer expressly disclaims responsibility therefore. Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict with existing laws and/or patents covering any material or use.